lasasmaniac.blogg.se

1. MINICOM SETUP INSTALL
2. MINICOM SETUP SERIAL
3. MINICOM SETUP SOFTWARE
4. MINICOM SETUP TRIAL
5. MINICOM SETUP OFFLINE

Remember to select Save setup as dfl prior to exiting and using the new settings. After the desired settings are inputted, press enter to move onto the next column, and repeat until the previous menu is displayed. c 1) and a line delay of one millisecond (i.e. In the above example there is a character delay of one millisecond (i.e. The usage list can be generated by typing ascii-xfr in a terminal session. v: verbose (statistics on stderr output) d: set End Of File character to Control-D (instead of Control-Z) e: send the End Of File character (default is not to) Below contains a list of switches for Ascii-xfr: Now here is the tricky part, by changing some switches for ascii-xfr we can have our transfer create a delay after every character or line is transferred, among other things we will not worry about here. Now, a courser should appear next to ASCII, however we do not want to edit the “name” column, so press Enter to continue onto the “Program” column. To edit this section press the “I” key which corresponds to the row ASCII is in. | Change which setting? (SPACE to delete) |Īt this point we will only be interested in the “ascii” section which uses the program “ascii-xfr”. | I ascii /usr/bin/ascii-xfr -dsv -c 1 -l Y U N Y N | | H kermit /usr/bin/kermit -i -l %l -r N D Y N N | | G kermit /usr/bin/kermit -i -l %l -s Y U Y N N | | D zmodem /usr/bin/rz -vv -b -E N D N Y Y | | A zmodem /usr/bin/sz -vv -b Y U N Y Y | Select “File transfer protocols” and now the following should be displayed:

MINICOM SETUP TRIAL

The final remedy may require some trial and error on your part.

MINICOM SETUP SERIAL

Sometimes the serial devices do not talk to each other nicely resulting in one being overloaded by the other. If file transfer fails or hangs, some additional tweaks in Minicom may be needed.

|Īfter following the prompted instruction to continue, use the appropriate D-Bug12 instruction to run the transferred. |Ĭopyright| READY: press any key to continue. |Line delay: 2 ms, character delay 1 ms | After a successful transfer has been completed, the following should be displayed in terminal: After selecting a file (.s1 record file) for upload press Enter to transfer. Use the Up and Down arrows to select a file or directory Press the space-bar key twice to enter a directory or to select a file Select the “” located at the top to enter a higher directory or previous directory. Note: Directories preceded with a period are “hidden” folders and should appear before all non-hidden folders. Minicom will now display a text based folder navigation, for example:

MINICOM SETUP OFFLINE

Thus far you should see:Ĭopyright 1996 - 2005 Freesca+-+torĬTRL-A Z for help | 9600 8N1 | NOR | Minicom 2.3 | VT102 | Offline Then press Ctrl+A and press the S key for “upload”.

To transfer a text file to the Dragon12 board, type in load in D-Bug12. You should receive the following D-Bug12 prompt:Ĭopyright 1996 - 2005 Freescale Semiconductor Note that it is unimportant if the device was connected before or after configuration. Once the Dragon12 is connected to the serial port, press the “reset” button on the board. Minicom is now 'listening' to the serial port (/dev/ttyUSB0 is the serial device is in this example). The following sequence should appear:įollowed by something similar to the following: Type minicom in a terminal to run Minicom. Selected Save setup as dfl (save setup as default) then select Exit from Minicom. When the configuration is complete you should be presented with the original screen.

MINICOM SETUP SOFTWARE

| G - Software Flo| D: 38400 O: Mark V: 8 | | | F - Hardware Flo| C: 9600 N: Odd U: 7 | | | B - Lockfile Loc| Current: 9600 8N1 | | To edit the baud rate and related settings press the 'E' key.You should be presented with the following: Press the 'G' key to toggle Yes or No.Press the 'F' key to toggle Yes or No.You should be greeted with the following screen: Next, select “Serial port setup” and press to continue. Now the following menu should be displayed: To start the configuration process type in the following command and switch: Now that Minicom is installed, the program must be configured properly to interface with the board. It would be best to use your distributions' repository if possible.

MINICOM SETUP INSTALL

Minicom can be downloaded from Freecode or the following terminal command can be used to download and install the program:ĬAUTION: I've seen some potentially fake sites posing as the 'official' Minicom website with untrusted security certificates. This program is used from console to interface with D-Bug12 and send the text file to the board. Minicom is a serial communication program, which we can use with the Dragon12 board.

Project maintained by Derrekito Hosted on GitHub Pages - Theme by mattgraham Introduction